Close
(0) items
You have no items in your shopping cart.
All Categories
    Filters
    Preferences
    Search
    Brand: Hilift

    HI-LIFT ALL CAST JACK (60")

    R 4 895.00
    HI-LIFT ALL CAST JACK (60")
    Item Number: HL605
    Availability: 2 in stock

    Hi-Lift® All-Cast Jack

    The Hi-Lift Jack Company offers the only all-cast jack manufactured in the world today. Our casting jack is manufactured from high yield and tensile strength iron castings, the same durable metal that we have used for over 100 years.

    • All-Cast Construction.
    • 7000lb (3175.14kg) Tested Capacity.
    • Available in 42", 48", & 60" Heights. (107, 122, & 152cm)
    • Lifts, Winches, Clamps, & More.
    • Most Durable Design

    Troubleshooting

    Getting the most out of your Hi-Lift Jack

    Before attempting any of the "Troubleshooting" items; clean the jack thoroughly using a NON-FLAMMABLE solution; lubricate the edges of the upright Steel Bar and all working parts with light oil (note the lube points shown on the "Parts Diagram").

    Important Notes:

    Never service your jack nor attempt repairs to the jack while it is under a load. The lifted load must be approximately 150 pounds or more to lower step-by-step, otherwise, the lifting mechanism will automatically return to base level.

    Click to view the Hi-Lift Jack Parts Diagram


    Troubleshooting Steps

    1. Check For Visibly Broken or Worn Parts
    2. Check Running Gear Installation
    3. Lock The Reversing Latch
    4. Inspect Cross Pins
    5. Inspect Reversing Switch
    6. Check Reversing Switch Spring
    7. Inspect Climbing Pin Springs
    8. Confirm Proper Installation of Climbing Pin
    9 . Check for Proper Function of Climbing Pins
    10. Check Safety Shear Bolt

    REPLACING THE REVERSING SWITCH (PART #C5)

    Place the Reversing Latch (Part #C4 or S4) in the up or locked position. Remove the Cross Pin (Part #26) from the upper Climbing Pin (Part #29). Move the Reversing Latch to the down or disengaged position. Remove the Cap Screw (Part #22A) and the Reversing Latch. Pull the Reversing Switch outward and down until it rests on the upper Climbing Pin. Keep the Reversing Switch as low as possible and with a screwdriver, push the Reversing Switch Spring (Part #27A) off the catch on the Reversing Switch. Allow the Spring to drop down behind the Reversing Switch. CAUTION: DO NOT OVER COMPRESS NOR BEND THE SPRING! Remove the Reversing Switch. Install a new Reversing Switch (and Reversing Switch Spring, if necessary); replace parts in reverse order.

    CAUTION: MAKE SURE THE BEVELED SIDE OF THE CLIMBING PIN IS UP WHEN INSERTING THE CROSS PIN. ALSO, LEAVE 1/32" CLEARANCE BETWEEN THE BOTTOM OF THE CROSS PINS AND THE BRIDGES OF THE LARGE RUNNER (Part #C10) AND SMALL RUNNER (Part #C1).

    Parts Diagram

     

    Running Gear Diagram

    Parts List

    1. Top clamp-clevis (C7 or S7)

    2. Top clamp-clevis bolt & nut (20-21)

    3. Steel standard bar (B42C, B48C, B60C, B36P, B42P, B48P, or B60P)

    4. Reversing latch (C4)

    5. Handle clip spring (31)

    6. Cap screw with washer (22A)

    7. Steel handle with cotter pin (15-25)

    8. Handle socket (C2 or S2)

    9. Pitman pin (30)

    10. Pitman (C3 or S3)

    11. Hex bolt & nut (16A-17)

    12. Large runner (C10)

    13. Reversing switch spring (27A)

    14. Reversing switch cam bar (C5)

    15. Cross pin (26)

    16. Climbing pin (29)

    17. Climbing pin spring (28)

    18. Small runner (C1)

    19. Shear bolt & nut (18A-19)

    20. Foot piece with cotter pin (C6-24 or S6-24)

    21. Complete running gear (RGC or RGP)

    Instruction Manuals

    All Hi-Lift products are serviceable and come with a 1-Year Warranty. Click below to download instruction manuals for our full lineup of products.

    Write your own review
    • Bad
    • Excellent

    Hi-Lift® All-Cast Jack

    The Hi-Lift Jack Company offers the only all-cast jack manufactured in the world today. Our casting jack is manufactured from high yield and tensile strength iron castings, the same durable metal that we have used for over 100 years.

    • All-Cast Construction.
    • 7000lb (3175.14kg) Tested Capacity.
    • Available in 42", 48", & 60" Heights. (107, 122, & 152cm)
    • Lifts, Winches, Clamps, & More.
    • Most Durable Design
    Customers who bought this item also bought

    HI-LIFT ACCESSORY BUMPER LIFT

    BL-250
    R 420.00
    HI-LIFT ACCESSORY BUMPER LIFT

    HI-LIFT ACCESSORY FIX IT KIT

    FK-1
    R 975.00
    HI-LIFT ACCESSORY FIX IT KIT